V2, the next generation...

Whats currently going on / was gerade passiert
Post Reply
User avatar
bofh
Posts: 629
Joined: Tue 1. Jun 2010, 19:01
Location: Saarland
Contact:

Re: V2, the next generation...

Post by bofh »

habs verschoben!
Metz
Posts: 393
Joined: Tue 1. Jun 2010, 18:12

Re: V2, the next generation...

Post by Metz »

Und werkelt auf anhieb :up:
Danke für die Settings.


Danke dir.


Launching /opt/avr/bin/avrdude -pm1280 -carduino -P/dev/ttyUSB0 -b57600 -Uflash:w:multidisplay.hex:a
Output:

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x1e9703
avrdude: NOTE: FLASH memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "multidisplay.hex"
avrdude: input file multidisplay.hex auto detected as Intel Hex
avrdude: writing flash (44830 bytes):

Writing | ################################################## | 100% 10.94s

avrdude: 44830 bytes of flash written
avrdude: verifying flash memory against multidisplay.hex:
avrdude: load data flash data from input file multidisplay.hex:
avrdude: input file multidisplay.hex auto detected as Intel Hex
avrdude: input file multidisplay.hex contains 44830 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 9.28s

avrdude: verifying ...
avrdude: 44830 bytes of flash verified

avrdude done. Thank you.

avrdude finished
User avatar
bofh
Posts: 629
Joined: Tue 1. Jun 2010, 19:01
Location: Saarland
Contact:

AW: V2, the next generation...

Post by bofh »

:)

Hast deine V2 Platine fertig?
Metz
Posts: 393
Joined: Tue 1. Jun 2010, 18:12

Re: V2, the next generation...

Post by Metz »

Jupp.

Jetzt bräucht ich dann ne Belegung von was ist was. Button, N75 ect. Weiss ja ned wo welcher Pin jeweils hingehn soll.
User avatar
designer2k2
Administrator
Posts: 721
Joined: Mon 31. May 2010, 20:13
Location: Innsbruck
Contact:

Re: V2, the next generation...

Post by designer2k2 »

Neue VM :up:

Layoute jetzt den 3ten Abend an der V2, Zwischenstand:
currentwork.jpg
currentwork.jpg (101.83 KiB) Viewed 6147 times
Proto-V2 Prints sind Steckerkompatibel!

Was noch dazu gekommen ist:
- 3,3V Bluetooth Spannungsversorgung & Pegelwandler
- 3x Schaltblitz, es können jetzt 1 Stufe PWM und 2 Stufen Digital zugeschalten werden, wahlweise 5V oder 12V

Ich hoff das ich am Wochnende bestellfertig werd :beer:
itsmyfault...
User avatar
bofh
Posts: 629
Joined: Tue 1. Jun 2010, 19:01
Location: Saarland
Contact:

Re: V2, the next generation...

Post by bofh »

Metz wrote:Jupp.

Jetzt bräucht ich dann ne Belegung von was ist was. Button, N75 ect. Weiss ja ned wo welcher Pin jeweils hingehn soll.
Ich lad mal Stephans Grafik hoch.
Der Schalter fürs N75 (schaltet Masse) kommt an K11 (müsste der linke Pin sein).

Was ist denn unklar?
Attachments
MDV2ProtoConnect.jpg
MDV2ProtoConnect.jpg (114.12 KiB) Viewed 6139 times
User avatar
bofh
Posts: 629
Joined: Tue 1. Jun 2010, 19:01
Location: Saarland
Contact:

Re: V2, the next generation...

Post by bofh »

designer2k2 wrote: Ich hoff das ich am Wochnende bestellfertig werd :beer:
Wow, das wär extram cool.
Dann kann ich ja schon mal den Lötkolben vorheizen. :beer:
Metz
Posts: 393
Joined: Tue 1. Jun 2010, 18:12

Re: V2, the next generation...

Post by Metz »

Das hilft mir doch schonmal.

Beim N75 wusst ich nicht wo und beim Display wollt ich nix riskieren. Ist die selbe Belegung wie beim V1.

K-Line is mir grad wurst. Ham eh das VCDS und die Schalter waren halt noch wichtig.



An der stelle mag ich noch erwähnen das ich nicht weiss was Steff mit der Brücke von R28 / R29 gemeint hat. Wo soll ich da Leitungen WIE killen und umleiten?
User avatar
designer2k2
Administrator
Posts: 721
Joined: Mon 31. May 2010, 20:13
Location: Innsbruck
Contact:

Re: V2, the next generation...

Post by designer2k2 »

wenn du kein K-Line brauchst, lasst R28/29 einfach weg. Das auskreuzen ist nur für die K-Line wichtig, es wird aber nix kaputt wenn es sein lässt :idea:
itsmyfault...
Metz
Posts: 393
Joined: Tue 1. Jun 2010, 18:12

Re: V2, the next generation...

Post by Metz »

Geht mir nur drum weil ich die zwei Widerstände verlötet habe.
Und wenn ich des Zeug in nem halben Jahr vlt doch mal antesten will, such mer wie blöd den Fehler, weil ich das bisdahin dann vergessen hab.
Wollts dahe schon richtig machen.
Post Reply